How to Get a New Key for Subaru You can lock and unlock your Subaru at the touch of an electronic button if it is equipped with an electronic key fob. However, if your fob is tossed into the ocean or gets an immersion in the washing machine and you are looking for a way to fix it. Our Stocker Subaru dealership can help. First, you'll want to open the key fob case and find the transmitter circuit board inside. How to get a new key Getting a new key for a Subaru is easier than you think. It's possible to get a new key from a dealership, an automotive locksmith, or even online. Costs vary depending on where you obtain the key and if it needs to be programmed. It also depends on the type of key you have (transponder smart fob, push to start, regular non-transponder). If you're in search of a new key to your vehicle, you'll want to call an auto locksmith who specializes in Subaru cars. They'll know all about the unique key fobs and the specific programming that goes with them. If you're not sure what kind of key you're using, check the sticker on your windshield to figure it out. Certain keys come with Remote Start features that allow you to start your car from the comforts of your home. You'll also require the VIN number of the vehicle located on the label in the driver's side door or in the owner's manual. Subaru models made after 2000 come with a transponder key that disables the engine computer. These keys can't be copied using the same equipment used to cut traditional metal keys, so you'll need visit a locksmith dealer for replacements. A new key typically costs $50-$250, depending on the type of model and the features. How to Get a Replacement Key You can order an alternative Subaru key in several different ways, based on the model of your car (chip remote, intelligent or "push-to-start" remote, or a regular metal key). You can order a replacement key online, contact the dealership which you purchased the vehicle from, or an automotive locksmith who has the appropriate equipment to create the type of key you need. You can obtain an alternative key from your dealer. It will be sure to fit your vehicle and will be covered under warranty, and will be programmable for the specific model of your vehicle. The dealer will require codes for the car that you bought to create chip keys. This can only be done by the dealer from whom you purchased your vehicle. This can be a bit of an inconvenience due to the fact that you'll need either take your car there or have an automotive locksmith come out and code the key on site. The majority of locksmiths and hardware stores have a huge selection of blank keys. To remove the battery, use a flathead screwdriver, or a metal key. Replace the battery using the CR2032 coin-cell and snap the encasement in place. How to get a key Fob A key fob is a tiny remote device that lets you to control the electrical systems. They can unlock and even start your car or lock it, set the alarm, and much more. It could be necessary to replace your Subaru key fob in case it isn't working properly. However, it is important to make sure that you are getting the right kind of fob for your car. Consumer Reports says that off-brand fobs can cause problems with the immobilizer system of your vehicle. If you have a newer Subaru you're likely to find that it's equipped with an intelligent key system. These require special programming to be compatible with your vehicle. This should be handled by your dealer and the cost could be covered by your warranty or roadside assistance program. Older Subaru models have keys made of metal which can be duplicated at a local hardware store or locksmith. You can also buy blank keys from online retailers who offer Subaru key with the Subaru logo. If your older Subaru has problems with its battery and you want to fix it, you can do it at home, without having to visit a mechanic or paying for a key duplication service. Look for a small crevice in the seam that divides the front and back of the fob. Use a flathead screwdriver pull the two halves apart. There's a flat battery inside. Take out the old battery and place the new 2025 type battery in, making sure that the right side is facing upwards. After that, put the metal key in and pop everything together. How to replace the Key Fob In the past, it was common for people to purchase the key fob at a bargain price from a hardware store online and take it to a locksmith or dealer to be cut and programmed. It's still possible to do this, but it's better to go through the dealer. This will stop the key from being copied and will ensure that the new key fob has been correct for your vehicle. This is particularly important for vehicles with more recent model that requires special programming, for example, those with features like automatic parking and window rolling. They are great to use when driving your Subaru in Gilroy but they can also be an issue when the buttons stop working. You can change your key fob's battery on your own, in case you're familiar with the process. Begin by locating the tiny gap in the seam which separates the front from the back of your fob. Use a flathead or the tip of a metal screwdriver to remove the fob and then look inside for the flat round battery. Remove https://www.g28carkeys.co.uk/subaru-car-key-replacements-near-me/ and replace it with a 2032-sized battery. Make sure the battery is facing the same direction as the original. Reassemble your device. In the near future it is possible to have your car keys replaced with "smart" keys with additional features. You can still enjoy the features of your Subaru key fob until that time. It will automatically open your window while your engine is running.