Replace Lock in UPVC Door If you have a Upvc door lock that isn't functioning properly you should call in a professional locksmith. They are fast efficient, reliable, and will complete the task to a high standard. The process of changing a barrel lock made of upvc isn't that difficult to do. It's just a matter of knowing the procedure and follow the steps below. Remove the barrel lock uPVC windows and doors are typical in all kinds of properties. They are great for allowing natural light into the home and are simple to open using the right key. It takes only five minutes to replace the barrel of a lock on uPVC uPVC. If you have lost your keys, a tenant has left but has not returned them, or the lock barrel has been damaged and needs to be replaced, this is an easy solution. You'll need to remove the handle screws first. The handles will be removed of the way to allow access to the barrel screws for the lock. You should not loosen the screws quickly because this could damage the handles. Once the screws have been removed After removing the screws, look for the screw that is on the inside of the door that is holding the barrel lock in place. It is a screw that stands out and is a different color than the other screws on the door. Utilizing the Phillips screwdriver, remove this screw. You can take the key you use to open the lock and place it inside the barrel. Turn it to the left as much as possible. This should release the barrel and make it easier to pull it out of the door. After loosening the screw, you can now break the pins that hold the Euro Cylinder. To accomplish this, you'll need strong pliers or mole grips. Grab the protruding part of the euro cylinder, and bend it from side to the side and upwards and downwards. This will break the two support pins that hold it in place. The installation of the new cylinder will be done after the old one has been removed. First, you will need to measure the size of the lock cylinder to ensure that you have purchased the correct replacement. This can be done by measuring the distance from the center of the circular part of the keyhole to the center of the square spindle. The measurement must be taken from the upper spindle hole. Modifying the Cylinder The primary locking mechanism is a euro cylinder. It is simple to replace and does not require a locksmith or handyman. If yours does not have this security feature, you must replace it with one that has. They aren't expensive and could help you save money and time in the event that your locks are compromised. To start to begin, open the door and stand in front of it, so that you can easily reach the screw for retaining the handle by hand or using a suitable tool. It is possible to loosen this screw a little bit maybe a quarter-turn to get started. The cylinder should now be easily removed since the screw will stop holding it in position. The next step is to decide on the size of replacement cylinder you require. There are approximately 25 sizes available. It is a good idea to bring your old cylinder with you when you purchase a new one so you are sure it will fit. If you're unsure of the dimensions, measure from the screw hole center to the cylinder's end. You can only be sure that you are buying the right sized cylinders to fit your upvc door by measuring from the center of the screw hole to the end of the cylinder. Insert the new cylinder into your door in the opposite direction you removed the old one. It could be difficult to align the lock cam but this is usually just an issue of alignment and should come right eventually. Now you will need to install the long screws for securing. After that, you are able to test it to make sure that the cylinder is secure in the door. If you are happy that it is, then reattach the handle and close the door to check again. If everything is working as it should your cylinder lock on your doors made of upvc has been replaced and you've added a layer of security to your home. Change the Handle T https://www.repairmywindowsanddoors.co.uk/altrincham-window-lock-repairs-near-me/ are a variety of reasons the handle of a door or door knob can become loose. It could be due to wear and tear of the handle or the square spindle within the handle. In this case the door handle will need to be replaced. First, ensure that the door is open and doesn't close between removing and replacing the handle. Remove the screws from the interior surface of the handle plate by using the help of a screwdriver. This will free the handle from the plate. Don't lose the screws, as you may have to replace them later. You can now remove the handles to gain access to the cylinder lock inside the door. The cylinder lock is round or bulb-shaped, and is only found in multi-point locks for upvc and some aluminum doors. It is the same as changing the handle. The only difference is that you'll need to remove the old cylinder out of the door and replace it with a new one. It is important to take into consideration the size of the handle replacement when choosing one. Make sure the handle you choose is of a similar size to the original as it will need to fit over the screws that keep the handle in place. The best place to begin is by referring to a size matrix which will list the most common sizes of replacement handles along with their keyhole center to handle plate distance. Consider upgrading your door handles made of upvc to a higher security standard such as a Sold Secure SS301 set or 2* Kitemark security handles. This will increase the security of your home and making it a lot easier to operate the door. The price of these sets might be a little more expensive, but the peace of mind and security is worth it. Having to constantly push the handle of the door upwards and downwards to shut or open it is not something you would like to be doing. Change the Lock The security lock on your uPVC door could be a weak point for thieves. You might want to upgrade your uPVC door to a multipoint lock to make it more secure. This would include an open hook as well as a deadbolt to keep out burglars. A professional locksmith can assist you with this, however it is also possible to complete the work yourself. You'll need several tools, but the process is simple and fast. The first step is to loosen the screws that hold the handle in place. You can take the screws off using the help of a screwdriver, and then store them in a secure place. You can then raise the handle to reveal the screw that holds the cylinder in position. The screw can be removed and replaced with a brand new one. Make sure the screw is of the same size as your original. It should be aligned properly with the barrel of lock. Changing the lock of your uPVC door can be a challenge. It is vital to the security of your home. If you make a mistake, it could cause you to be unable to open the door. If you are aware of how to do it, the process is relatively simple and will cost you less than hiring a locksmith. To change the lock on your uPVC door, you will need to access the inner faceplate of the lock. You must be able to identify the screw on the inside of the door as well as the bolt that holds it on the outside of the door. Once you have these screws in your hands, you can remove and replace the faceplate. It is possible to replace the lock on your uPVC door for a variety of reasons. It could be a lost key, or a tenant moved out but did not return keys, or you want to increase the security of your home. A change in a uPVC locking mechanism can be accomplished by anyone with basic DIY skills. You will need to inspect the hinges inside the mechanism, which could be a difficult task if the lock is sticking. If the hinges are lubricated, it should be simple to repair. However, if you're not confident doing this, it is best to call a professional.