Replace Lock on Your UPVC Door Yourself You can replace the lock on your upvc door by yourself, as long as you have access to both sides of the handle faceplate. You'll need a screwdriver, an extended bolt, as well as a key. Sometimes a uPVC door mechanism may become stuck because it is unlubricated or something inside has been damaged. It's easy to fix when you are aware of what you're doing. Preparing for repairs uPVC door problems can vary in severity. You may be able repair the issue yourself when your uPVC lock becomes stuck or is misaligned. But, it is crucial to ensure that you do not to cause any damage to the lock mechanism as this can cause more damage. It is also recommended that you try to avoid using lubricants such grease or oil since they can cause the locking mechanism to become sticky. Instead, you should use light machine oil or graphite powder as these are safer and won't harm the uPVC door. A uPVC barrel for doors can be a challenge to remove once it is installed, so be aware of what you are doing before you begin. It is recommended to hire locksmiths if not experienced with this type of repair. They will ensure that the work is done properly. This will save you time, since they can complete the task quickly and efficiently. The first step is to take out the screw which holds the barrel in the first place. It will be of different to all the screws on the door. It is located in the inside edge of the edging, near the faceplate of the lock. Once the screw is removed, you can then slide the barrel lock out. When the lock is gone you can then take off the handle and replace it with the new one. It is important to note that a locked uPVC door can be shut and opened without the handle. The uPVC door comes with a built-in security system, referred to as multi-point locking. This system comprises of two hooks at the top and bottom of the door, along with a latch or dead bolt in the middle. This allows for an extremely robust and secure door. If your uPVC door is locked and you are unable to open it the most likely issue is with the locking cylinder. The uPVC lock cylinder is equipped with a specific key and is therefore not as easy to break or displace as other locks. If you're unfamiliar with this type of repair, it's best to get a professional locksmith. Remove the Cylinder The cylinder, also known as the barrel, is a small component in the handle of the handle of a uPVC door that allows you to lock and unlock the door. It is usually made of pin-based technology and while it has been effective for a long time, it is now being targeted by criminals looking to improve their chances of gaining entry into your home. You can increase the security of your home by replacing the cylinder. To remove the handle first, you must loosen the screws holding it in place with a Phillips-head driver. Save these screws to use them to re-attach the handle after the task is completed. Locate the pinhole in the inside trim and handle that keeps the handle in place. Find a straightened clip or another pin to put into the hole. When you turn the handle apply pressure to the pin to release it. Once it's released, you can pull the handle towards you to pull back the latch in the cylinder. After the cylinder is loose and removed, you can remove it by hand. Be careful not damage the threads on either side of the cylinder, or the cam in the middle. If the cylinder isn't being able to slide out it could be pinched by the handle furniture or the locking mechanism and must be released to allow it to slide out. If you're ready to replace the cylinder, look for one that has been rated by an independent testing agency to meet minimum standards for anti-snap as well as anti-bump protection. There are numerous types of locks available on the market. It is important to consider your needs prior to selecting the right replacement. If you can, bring the cylinder you have used to the store so that you can ensure that you're buying a suitable replacement. There are approximately 25 different sizes of lock cylinders to choose from and it is therefore essential to accurately measure yours. Reinstalling Cylinder If your locks aren't working properly, you might need to replace them. It is possible to replace your locks for several reasons, such as to increase security or satisfy insurance requirements. It is also possible to replace your lock if you've lost keys or recently moved into a new home. Whatever the reason, changing your uPVC door lock isn't difficult and can be accomplished by anyone with a bit of guidance. First, ensure that the door is propped or secured so that it does not close during the procedure. Next, remove the screws that keep the handle in place by using a screwdriver. Remove the screws slowly or small pieces may fall off. Slide out the interior and exterior handles simultaneously after removing the screws. This is a bit difficult, but it's essential not to force anything. This could cause damage to the mechanism of the handle and cause the handles to break. After the handles have been removed, locate the cylinder fixing screw on the outside of the door. This is usually an enormous screw that is in line with the lower portion of the cylinder. https://www.repairmywindowsanddoors.co.uk/west-bromwich-window-lock-repairs-near-me/ should be a different colour from the other screws and be easy to identify. Turn the screws around to loosen them, then take them off. After removing the screw you should be able to see the cylinder within its socket. Insert your key, and turn it both left and right. This will help unlock the cylinder. When the cylinder is unlocked, you'll have to gently pull it out of its socket. Place the new cylinder in its socket after taking out the old one. It should slide in easily If you're struggling trying to tug and wiggle it again. If you're not able to get the cylinder in, consider replacing the lock altogether. If you are replacing a euro-cylinder, ensure that it is equipped with anti-snap and anti-bump protection. These features will improve the security of your home and make it difficult for thieves to break into your home. Reinstalling the Handle There are a few reasons why your door handle made of uPVC might not be functioning as well as it ought to. Sometimes it's a matter of wear and tear but sometimes the problem is more severe. It could be that the cylinder of the lock is damaged and cannot be repaired, in which case it's time to replace it with a new one. First, you'll need to remove the old handle. This isn't difficult to do and you can usually do it by removing the two screws that hold the handle in place using the help of a screwdriver. Once the screws are removed there should be nothing securing the handle to the door, and it should fall away with very little effort. It's a good idea clean the spindle and back plate following the removal of the handle. This will ensure that there is no dirt or grime to cause problems with the new handle. It's also a good idea to give the handle a clean with a cloth to make sure it is free from dust and dirt as this can impact the performance of the handle. Before you reinstall the new handle take an inspection of how it fits on the door, in most cases, the hook plate and the roller face plate are able to fit into a recess in the centre lock case to ensure there isn't any gap between them. If the handles aren't fitted properly it can exert an excessive amount of pressure on the central lock case and pose a risk that something might break inside. Begin by slipping the spindle through the hole on the exterior handle, and then into hole of the handle inside. It is possible to tap the spindle lightly using a mallet or hammer to allow it to slide into place. Once you've got it in place, there is probably a small screw for retaining at the end of the spindle. must be tightened, line up the holes, and then replace this screw.