Door Handle Replacement It's worth it to replace door handles if you don't like the way they look or if they're difficult to use. With some patience, you can put in the new handle in no time. Modern door handles are often equipped with cover plates that conceal the screws for a more attractive appearance. If your new handle does not have screws already connected, you'll need to attach them separately. Remove the old handle The door handle isn't just a decorative feature for your home it also serves as an important safety feature that lets you to lock and unlock your door. However, over time your door handle can lose its grip, appear loose, or appear old and worn out. This is a sign that it's probably time for a replacement. If your door handle is becoming difficult to use, it could be time to replace it. This is a problem since it means that you can not lock or unlock your door, which could pose an security risk to you and your family. It's also recommended to replace your door handle in the event that it's damaged or broken. A damaged or broken door handle could be quite dangerous, especially in the event that your children or senior family members have difficulty opening it, and get trapped in the. It's a good thing that it's easy to fix a broken door handle by replacing the handle that was broken. The majority of modern door handles are standard size, so they will fit on any door. If you aren't certain that your new door handle will work, take off the old one and take measurements of its holes in the housing. This will help you to buy the right door handle. It is the easiest method to remove the old door handle by taking it off from the door. This is usually done using the screw driver. However, some door handles have a cover plate that conceals the mounting screws so you'll need to remove this to reach the screws beneath. After you have removed the handle that was previously used, take note of the way in which the spindle is connected. This will aid in aligning the new handle. https://www.repairmywindowsanddoors.co.uk/canveyisland-windowrepair/ can also remove the door handle by removing the latch mechanism. This is typically done with the screwdriver, but you'll need to locate the small latch, which should be at the edge of the trim piece. Once you've removed the latch, take the handle off the strike plate and then remove the latch off the door's edge. Removing the Strike Plate When you replace your handle, you'll need to replace the latch plate, which is the hole that the door's latch hooks into when it closes. The new handles will have two latch plates that are circular and rectangular plate (see the above diagram which shows the various parts of a door handle). If you have a rectangular latch plate, swap it with a round one. This will allow the latch to be able to hook into the strike plate and make the handle easier. The first step is to loosen the screw that holds the latch plate that was previously in place. The screws are often quite tight and require a bit of force to loosen them. If possible, it may be beneficial to have another person assist with this part. After the screws are removed, the latch plate should slide out of the door easily. If it is stuck or doesn't move, use a small nail file to scrape around the edges of the latch plate. This can sometimes free up the plate. Now you can move on to making the new door strike plate for installation. Utilizing the screws made of wood that came with your new handles, attach the latch plate onto the inside of the doorjamb. Do not tighten the screws too much as this could damage the strike plate. If you're unsure if the latch plate is in the correct position You can try closing and then opening the door to determine if it closes and latches correctly. If not then you'll need to adjust the strikeplate upwards or down, forward or back until the door closes properly. If the door continues to move or jiggles, then you may have to expand your latch hole on the strike plate. This is more frequent in older doors, however it could also be caused by wear and tear hinge mortises that are not deep enough or the wrong size for the latch, or due to damaged or broken strike plate. If this is the case then you should use a filing made of metal instead of a chisel, or hammer to adjust the strike plate. Removal of the Latch The latch is a curved metal piece which slides in and out of a hole on the inside of your door. The latch is pushed forward when you turn the handle. It also connects to a hole in the frame of the door to keep the door shut. If your door shakes when you close it, changing the latch may be all that's needed to correct the issue. It's hard to see the screws that hold the latch to the door, however there's usually a small hole on the trim plate that lets you to insert a screwdriver in order to pry it off. After taking off the trim plate you should be able to remove the latch, as well as the bolts that hold it, as well as the spindle in position. If the latch cannot be easily removed using a paperclip or tool to take it off the handle mechanism. Insert the item into the recessed latch slot and gently twist it or jiggle until you feel the that the latch and handle begin to separate. You may need to repeat this procedure several times before you can pull the latch out. It should be possible to slide the new latch into its slot without any issues once you have removed the old one. Use the new screws to connect the latch to the strike plate or door frame. Make sure it is correctly placed in the slot and aligned with the screw chambers. Before installing the new handle, make certain to measure your existing backset (the distance from the center of the big hole on the front surface of the door to the edge). Make sure that the size of the latch of the new handle is in line with the measurement. If you are replacing the handle or latch or handle, or if the old lock cylinder has been damaged, then you will need a new one. If you're not changing locks, a new lock should fit in your existing recess and will work with your current keys. Make sure you select an entry point with rectangular cover plates that match your old handles. Take off the cover plate You can replace your door handles with a modern design of roses and levers to enhance the appearance of your home. You can buy complete sets of escutcheons, the escutcheons as well as privacy adaptors and escutcheons. To replace an internal door handle remove the cover plate (or rose) that covers the screws and mechanism. Use a flathead for removing the cover plate. It may have a slot along one edge or be held in place by pins. Remove the screw that holds the handle in the interior and put it aside after the cover plate is removed. It is also necessary to remove the screws that hold the latch and plates and the latch plate, which can be done by loosening them using a Philips screwdriver. Take the inner plates and latch from the door. Set them aside. Not all doors have this gap. If yours does not have a handle, you'll need to drill a new hole in the door. This is the same procedure as opening a door locked, but you will need to be extra careful not to damage the door's frame or frame. After drilling the holes after which you'll have to put in new screws for the door knob. Make sure to buy the same size as the old ones, so you don't end up with a handle that's too tight or too loose. You'll also need to install an additional strike rod and latch plate, which aren't included with the majority of door handle sets. If you're looking for a quality replacement set of interior door handles, try the Amazon's Choice FAERSI two-piece chrome-finished handle set. It is a factory-fit and has received hundreds of 5-star reviews. It's a great choice for replacing worn or damaged interior door handle hardware on your Chevy HHR.