Replacing uPVC Window Handles Switching the handles of windows made of upvc is a fairly straightforward task. It is important to make sure that the new handle is a good fit for the spindle carved out in the window mechanism. If you follow the steps below, any cockspur handle will fit in most windows. The most important factor is the step in the height of the handle. What to Do You Look For? A lot of windows in the UK are fitted with uPVC handles, and over time they will begin to show signs of wear and wear and tear. When this occurs, the window handle could become shaky or difficult to operate, making it necessary to replace it. Anyone who is comfortable using a basic hand tool is able to complete this task. The first thing to do is ensure that the handle is firmly fixed to the window frame, and is in an open position. The next step is to locate the screws or pins that secure the handle in place. They are typically located on the inside of the handle. They can be removed using an screwdriver or pliers. Once the handle is loose and sagging, it can be removed from its hinges by gently pulling it off. Then, you'll have to locate a new handle in the same style and size. This can be done at the DIY store or on the internet. The process should take about five minutes, and you will need a screwdriver is all you need. When replacing a uPVC handle, it is important to think about the step height. This is the distance from the base of the handle until it is placed on the window frame. It is generally an average measurement, but it is crucial to determine the step height of your current handle prior to ordering a new one. Depending on the kind of handle you choose, there are different sizes to choose from. Inline handles are available for uPVC windows that have centers of 31mm for lugs, while cockspur handles have centers of lugs of 43 millimetres. Tilt and turn handles are commonly used on windows made of uPVC, and they have a special design that allows the window to be slid up for ventilation, and then rotated to open the window completely. The most common cause of breakage in uPVC handles is that they crack internally instead of breaking off from the base section. This can make them hard to open and is why it is important to make sure that any replacement handle you buy has the same length of spindle as the one you have. Take off the handle from the old one. Incorrectly fitted or damaged window handles may cause your double glazed windows to open or close incorrectly, and can result in them getting stuck. There are many reasons for this, such as general wear and tear or corrosion of the handle made of metal. In these cases it is crucial to seek replacement handles made of upvc as soon as you can to avoid further damage and loss of functionality. One of the first things to do when replacing window handles made of upvc is to remove the old handle from the window. To do this, start by getting rid of the screw that is covered when the handle is in a closed position. After you have removed the screw, you are able to remove the handle. It is recommended to make use of an electric screwdriver for this since it will make the job easier and faster. Be aware that screws can be hidden in plastic caps. It is best to remove the covers with a Stanley knife. After you have removed the old handle, you'll need to check the square cutout on the base to ensure that the new handle you choose for the window lock is compatible. It is essential to measure the length of the spindle on the handle that was used and compare it to the size of the window mechanism spindle cutout. The different kinds of window handles made of upvc are: Espag handles, which are equipped with a central screw and will turn left or right; Cranked handles which have two screws and are found on tilt and turn upvc windows as well as Spade handles, that have a flat arm and can be placed on either side of the window. Once you have found a suitable replacement, it's simply a case of screwing the handle in place and ensuring that the spindle is fitted into the lock mechanism. Once you have done this you can tighten the handle onto the window frame. The new upvc handles will now be secure. Take a measurement of the Spindle If you're replacing a upvc window handle that has come off, it is likely due to the spindle that holds it in place is loose or damaged. In certain situations you can tighten the spindle using a screw or pin. In other instances, it may require replacement completely. There are many different kinds of handles made from upvc. There are three types of handles: inline espagnolette tilt-and-turn, and cockspur. Each kind has a distinct procedure for installing and replacing the handle. Before https://www.repairmywindowsanddoors.co.uk/derby-windowrepair/ purchase a new handle, it's important to know the size of the existing one. This will help ensure that the new handle is the correct size and fits into the window. Fortunately, all handles follow industry standard sizing so it's fairly easy to find the correct size. To determine the size of your handle first remove it from the window by turning it back to the open position. Then, you should be able to determine the size of the screw or pin that secures it. Then, use a tape measure or ruler to determine the length of the spindle. Once you have determined the length of the spindle, you can purchase a replacement spindle that is the same length. When you are looking to replace a handle, it is important to take into consideration the step height of a upvc window handle. The step height is the distance from the bottom of the handle to the point at which it rests on the frame. This is usually about 21mm or 9mm for aluminium and uPVC. To be sure that the new handle will fit it, you can drop something into the gap to see how far it extends before it meets an obstruction. Cockspur handles may have different backsets depending on what type of window you put them in. Inline Espag handle heights are 43mm from the centre to the centre (two fixing points). Cockspur handles, however, have different backset heights depending on the design of the window they are in. This is due to the fact that they have a spur that extends from their handle and is locked onto a cockspur wedge-striking plate. Fit the New Handle After you've chosen the new handle, align it carefully with the screw holes on the door. Then, secure it with the screws supplied. Install the latch lever in the same way as the handle that you are replacing in the event that you are replacing the door handle. After that, attach the door trim to hide the mounting screws and close the job. Tips: To take the head made of metal from the wedge made of wood Hold the handle so that its longer end is resting on the floor. Use a hammer to tap on the thin end of the handle. Be careful not to scratch the handle or the spindle.