Replace Lock on Your UPVC Door Yourself You can change the lock on your upvc door yourself, as long as you have full access to both sides of the faceplate. You'll also require an screwdriver, a long bolt and an entry key. Sometimes a uPVC mechanism can become stuck due to a lack of lubrication or if there's a problem inside. This is a simple fix If you know what you're doing. Preparing for repairs uPVC doors are susceptible to a range of issues and some are more severe than others. It is possible to solve the issue yourself if your uPVC lock becomes stuck or is misaligned. It is important to ensure that you do not damage the mechanism of the lock, as this could make the issue worse. It is also recommended to avoid using lubricants like oil or grease, which can cause the locking mechanism to become sticky. Instead, you should opt for graphite or light machine oil as they are safer and won't harm uPVC. It can be difficult to take off a uPVC door barrel after it is installed. It is therefore important to take your time before you begin. If you're not familiar with this kind of repair, you should seek the help of a locksmith to ensure that the task is completed correctly. This will help you save time, since they can finish the task quickly and efficiently. The first step is to remove the screw that holds the lock in place. This will be of a different color to all the screws on the door and is located on the edging on the inside close to the faceplate of the lock. After removing the screw then you can slide the barrel out. After the lock has been removed, you can remove the handle. It is important to know that a locked uPVC can be shut and opened without the handle. The uPVC has a built-in security system known as multipoint locking. This system is comprised of two hooks on the top and bottom, plus the deadbolt or latch in the middle. This results in a strong and secure door. If you can't open your uPVC doors, it's most likely the locking cylinder. The uPVC lock cylinder can be fitted with a special key, and therefore is not as easy to break or displace as other locks. If you're unfamiliar with this type of repair, it's recommended to get an expert locksmith. Remove the Cylinder The cylinder, also known as the barrel, is a tiny part of the handle of a uPVC door that allows you to lock and unlock the door. The pin-based technology is used and has been used for a number of years. However the criminals are now targeting it to increase their chances of gaining entry. By replacing the cylinder with a higher-grade lock, you can significantly improve the security of your home without having to pay for an entirely new locking mechanism. To remove the handle first, loosen the screws holding it in place using a Phillips-head driver. Save these screws to be capable of reattaching the handle once the task is completed. Find the hole that holds the handle to the trim. Find a straightened paper clip or another pin to put into the hole. Apply pressure to the pin while you rotate the handle to release it. When it is released, you can pull the handle towards you to pull the latch inside the cylinder. Once you have loosened the old cylinder, it is possible to remove it manually. Be careful not damage the threads on either side of the cylinder, or the cam that is in the middle. If the cylinder isn't being able to slide out, it may be being held by the handle furniture or the locking mechanism and will require loosening so that it can move out. If you're ready to replace your cylinder, select one that has been certified by an independent testing agency as meeting minimum standards for antisnap protection and anti-bump. There are several different grades of locks available on the market, so it is essential to know the requirements prior to deciding to select a replacement. If possible, take the cylinder you have used to the store to make sure that you are purchasing a matching replacement. There are about 25 different sizes of lock cylinders available and it is therefore essential to measure yours precisely. Reinstalling the Cylinder It is possible to replace your locks if they're not functioning properly. It is possible to replace your locks due to various reasons, including to improve security or meet insurance requirements. You may need to change the lock if you've lost your keys, or if you recently relocated. No matter what the reason is, changing your uPVC lock is not a difficult job and can be done easily by anyone with a little guidance. First, make https://www.repairmywindowsanddoors.co.uk/croydon-window-lock-repairs-near-me/ that the door is propped or secured in a way that it will not close during the process. Then, take off the screws that hold the handle in place by using the screwdriver. Be cautious not to remove the screws too quickly as this could cause small pieces to fly off and get lost. Once the screws have been removed, slide out both the interior and exterior handles simultaneously. This can be a little difficult, but it's crucial not to push anything. If you do, it could break the handles, and could also cause damage to the mechanism of the handle. Once the handles are removed, locate the cylinder fixing screw on the outside of the door. This is usually an enormous screw that is in line with the lower end of the cylinder. It should be a distinct color than the other screws on the door, and it must be easy to identify. Twist the screw to loosen it, then remove it. After removing screw, you can see the cylinder. Insert your key and rotate it in both left and right positions. Doing this will help to unlock the cylinder. Once it's unlocked, you can apply a moderate amount of pulling to take the cylinder out of its socket. Place the new cylinder in its socket after removing the old one. If you are having trouble, try wiggling or tugging again. If you can't get the cylinder in the lock, think about replacing it. If you are replacing a euro cylinder, be sure to purchase one with anti-snap, anti-bump or protection. These features will enhance the security of your home and make it difficult for criminals bypass the lock. Reinstalling the Handle There are a variety of reasons why your door handle made of uPVC might not be performing in the way it ought to. Sometimes it's just a case of wear and tear, but other times the issue is more serious. It could be that the cylinder of the lock is faulty and cannot be fixed in which case it's time to replace it with a brand new one. The first step is to take off the handle you used to have. It's not a big task. It is usually possible to remove the two screws using a screwdriver. Once the screws are removed there should be nothing to hold the handle to the door. it should pull away with very little effort. After you've removed the handle, it's a good idea to wipe down the back plate and the spindle hole to ensure there's no grime or dirt there that might cause problems when you replace the handle. It's also an excellent idea to give the handle a good clean using a cloth to make sure it is free from dust and dirt as this might hinder its performance. Before you replace a handle, make sure it will fit. In most cases the hook plate as well as the roller face plate are recessed into the centre lock case. There shouldn't be a gap between them. If the handles don't fit correctly, they can cause pressure on the central lock case, causing it to break. When you are ready to reinstall the handle, begin by slipping the new spindle into the hole on the outside handle, and then into the hole on the handle's interior. It might be necessary to tap the spindle gently with a hammer or mallet to help it slide into place. Once you have it in place there is probably a small screw for retaining at the end of the spindle that you must tighten and align the holes and replace this retaining screw.