Replacing uPVC Window Handles It is easy to change the handles on windows made of Upvc. It is important to ensure that the new handle is fitted into the spindle cutout of the window mechanism. If you follow the steps below any cockspur handle can fit in most windows. The most important thing is the step height of the handle. What to Look For https://www.repairmywindowsanddoors.co.uk/eastgrinstead-windowrepair/ of the windows in the UK are fitted with uPVC handles Over time, they can begin to show signs of wear and wear and tear. If this occurs, the handle can become loose or difficult to operate, making it necessary to replace it. Anyone who is comfortable using a basic hand tool can complete this relatively simple task. The first step is to make sure that the handle is securely fixed to the frame of the window in the open position. The next step is to find the screws or pins that secure the handle in place. They are usually located on the inside of the handle. They can be removed with a screwdriver, or pliers. When the handle is loose and sagging, gently pull it back from its hinges. Then, you'll have to locate a replacement handle of the same size and style. This can be done at the DIY store or on the internet. The process should take about five minutes and requires a screwdriver is all you need. One important factor to consider when replacing a uPVC window handle is the step height. This is the distance between the handle's base and the place it is located within the frame of the window. This is a typical measurement and you should check the step height before ordering the replacement handle. Depending on the type of handle you are using There are various sizes that are available. Inline handles are available for uPVC windows with lug centres of 31mm, while cockspur handles come with lug centres of 43mm. Tilt-and-turn handles are commonly found on uPVC windows. They have a specific design that allows the window to be tilted for ventilation and then turned to fully open the window. The most frequent uPVC handle breakage is internal cracking, rather than a fracture from the base. This can make it difficult to open. It is essential to ensure that the replacement handle is fitted with the same spindle as the original one. Remove the Old Handle If your window handles are damaged or incorrectly fitted, they could cause double-glazed windows to open and close incorrectly. They may even get stuck. This could be due to various factors, including general wear and tear on the metal handle or corrosion. In these situations it is crucial to find replacement upvc window handles immediately in order to prevent further damage and loss of functionality. When replacing the handles of windows made of upvc, you should remove the handles that were previously installed from the window. To do this, start by removing the screw that is encased when the handle is in the closed position. This should reveal another screw and once removed, you can begin to remove the handle itself. It is recommended to employ an electric screwdriver to accomplish this since it will make the job easier and faster. It is also important to note that the screws on the handle may be hidden behind caps made of plastic, so it is recommended to take an Stanley knife to the screws and take them off. After removing the old handle, you'll have to examine the square cutout on the base to make sure that the new handle for the window lock is compatible. It is important to measure the spindle length on the handle you used to replace it with and then compare it with the size of the window mechanism spindle cutout. The various types of window handles made from upvc include: Espag handles, which are equipped with a central screw and will turn left or right; Cranked handles which have two screws and are found on tilt and turn windows made of upvc as well as Spade handles, that have an arm with a flat surface and can be put on either side of the window. It is easy to replace the handle after you've found one that is suitable. Just put it in place and make sure the spindle is inserted correctly into the lock mechanism. Once that is done, it should be tightened to the window frame, and your new window handles made of upvc must be secure. Take a look at the Spindle If you're replacing a Upvc window handle that has fallen off, it's because the spindle that holds it in place has become loose or damaged. In some instances, this could be fixed by using screws or pins to tighten it. In certain situations it is necessary to replace the handle. There are a variety of handles made from upvc. They include espagnolette handles inline, cockspur handles, and tilt and turn handles. Each handle type is installed and replaced in a different way. Before purchasing a replacement handle it is essential to know the dimensions of the handle that is currently in use. This will ensure that the new handle is the correct size and fits within the window. All handles are sized in accordance with industry standards, making it easy to determine the right size. To measure the handle's size move the window to the open position. Then, you should be able to see the size of the screw or pin that secures it. Then you can use a ruler or tape measure to determine the length of the spindle. Once you have the length of your spindle, it is possible to purchase a replacement that is exactly the same size. When you are looking to replace a handle you should take into consideration the step height of the upvc window handle. The step height is the distance from the bottom of the handle until where it is placed on the frame. This usually is around 21mm or 9mm in aluminium and uPVC. To be sure that the new handle is suitable, you can drop something into the gap to check how far it goes before it comes into contact with an obstruction. Cockspur handles typically have different backset heights depending on the type of window they are installed in. Inline Espag handles have an average height of 43mm centre to centre (2 fixing points). Cockspur handles have different backsets based on which window design they are in. This is because they feature a spur that extends from the handle and locks over a cockspur wedge striker. Fit the New Handle After you've chosen the new handle, align it carefully with the holes for screws on the door. Then secure it using the screws provided. If you're replacing the latch lever, it can be installed similarly to the main door handle. Then, you can attach the door trim once more to hide the screws for mounting. Tips: To remove the metal head from the wedge of wood make sure the handle is held so that its wider end is resting on the floor. Use a hammer to tap the thin end of the handle. Be careful not to scratch the handle or the spindle.