How to Do a Door Lock Change Door lock change is a quick and cheap method to increase your home's security. However, the procedure is not for all. It requires a certain amount of patience and skill. You need to replace the cylinder, which is located inside the knob's body. The cylinder is responsible for recognizing the key when it is inserted into the lock. Removal of the old lock First, you must remove the lock that was previously in place. It's a fairly simple process, however there are a few things to remember. First, make sure that your new lock is the correct size for your door. This will ensure that it is secure and doesn't create a gap around the deadbolt or latch. Once you have removed the latch plate look for two screws or bolts on the inside of the casing that hold the casing and the two halves of the lock together. Unscrew these with a screwdriver, then take the lock out of the door. If you have a mortise locking mechanism there is a set screw that binds the handle to the spindle. Take off the doorknobs by removing the screw using the help of a screwdriver. You must also remove the deadbolt latch and latch plug from the hole in your door jamb. Install the new lock. If you are replacing a mortise lock, you should also measure the distance between the lock case and the door's edge to ensure that the new lock will fit. You may want to replace your lock for a variety of reasons, including when you suspect that someone else has the key, or if you've got a new roommate. In any case, you can save money by removing the lock yourself, rather than hiring an expert to remove it. It's much easier than most people imagine and can be done in a matter of a few minutes. Remove the trim and handle of your door. Then, pull the trim away with a flat screwdriver. You should be able twist off the majority of it. In certain cases, you may even be able to remove the handles completely. Then, check the handle for a tiny hole on the inside and insert a straightened clip into it. This will activate the release mechanism, allowing you to take off the handle. Then, look for another small tab that is located inside of the lock and press it with a screwdriver that is flat. After the spindle has been removed, you are able to remove the cylinder and the housing. Making a decision on a new locking system When it comes to choosing a new lock there are a lot of choices. Consider the different types of locks and choose one that fits the style of your door. Think about the backset, which is the distance between the edge and the center of the hole in the lock. Also, consider the cross bore, a small hole at the edge of your door's frame. Also, make sure to choose a lock that will be able to fit the door's thickness and swing. The American National Standards Institute and BHMA have graded the majority of door locks to give an idea of their durability and the difficulty to pick them up or disable them. A grade 3 lock may be ideal for a peaceful apartment building in a rural area, whereas locks of grade 1 might be better suited to the busy streets near the storefront. Most smart door locks need a digital code to open. If you are concerned about hacking, or any other security concerns, consult an expert locksmith. Replace the cylinder If the cylinder of your door lock is broken or damaged, you can replace it in a matter of minutes by completing a do-it-yourself project. It is essential to choose the correct cylinder and follow all instructions. The first step is to remove the knob or handle in the event that one is present and then remove the trim around the base of the lock cylinder using the aid of a screwdriver. After the trim has been removed, you can remove the screws that hold the cylinder with a flathead. The cylinder is then gently pulled out of the door. Before you install the new cylinder, be sure that it's the right length for the door you are using. With https://www.repairmywindowsanddoors.co.uk/oldham-window-lock-repairs-near-me/ , determine the distance between the cylinder's center and its right and left sides. Buy a new cylinder that has the same measurements. This will stop cylinders from snapping when the door is kicked or the key gets stuck inside. Place the replacement cylinder inside the door, and then turn the key. This will align the cylinder with your carrier that is usually located on the outside of your lock. You can then loosen the set screws, which should be only a couple of turns into the head. Also, you will need to loosen the screw at the edge of the door which secures the case if there is one. After taking the lock cylinder out after which you can replace it with a new lock by slipping the new cylinder into the case and tightening the set screw. The process of reinstalling the component that connects the cylinder to a lock indicator stem is also important. You can do this by pulling three small tabs at the back of the cylindrical using needle-nosed pliers. Attach the smaller bracket to the back of the cylinder. Then, you should reinstall the latch plate and strike plate, along with the retaining rings fixed to the top of the lock cylinder. Installing the new lock Begin by measuring the width of your door if you are replacing a lock that is already in use. Most residential locksets are designed for doors with a thickness of 1 3/8 - 3/4 inches. If your door is thicker you will require a door kit that is thick and includes longer screws, a longer tail piece (for door knobs) or spindle extension (for deadbolts). The majority of locks come with a comprehensive installation guide to aid you. Be sure to read the instructions thoroughly prior to beginning the process to ensure that you've followed all the steps. The booklet will also give you an idea of the level of skill required to complete the task. You might want to ask a person who has had experience in changing locks for assistance if are changing a lock the first time. It's a great idea seal the openings of the old lock before installing the new lock. This will keep the screws from falling out of the holes and will protect any tile you might have installed in the area. It also helps prevent potential damage from rust dirt, and grime. SECURAM Touch comes with an ad-hoc strip of masking tape or gaffer tape, but you can use any tape you have. After you have removed the screws that hold the lock's interior to the exterior and remove the lock immediately. This must be done quickly to prevent the lock from accidentally closing and damaging the mechanism. Install the new latch bolt into the upper cross bore of your new lock if it has one. Make sure that you place it in the proper location, which is indicated by an arrow. Then, place the latch plate onto the bolt and screw it in the correct position. Screw the deadbolt to the jamb on the door. Test the deadbolt a few times by throwing it to ensure it is extending into the strike plate. If you're using an electronic smart lock, be certain to follow the instructions for programming it. This involves downloading an app and registering your email address, verifying you identity, and connecting to the wireless network in order to connect your device.